Thailand's coastal industrial estates and island resorts have access to an unlimited water source — but the Gulf of Thailand and Andaman Sea bring specific conditions that SWRO plants must handle. Seawater in the Gulf of Thailand near Rayong and Chonburi typically carries TDS between 30,000 and 33,000 ppm, while Andaman Sea water near Phuket and Krabi runs between 32,000 and 34,000 ppm. But what makes Thailand's SWRO challenge distinctive is warm water temperature — 28 to 33°C year-round — which accelerates both mineral scaling kinetics and biofilm formation. This creates a combined scale-and-biofilm challenge that standard SWRO antiscalants handle poorly. Innova Corporate (India) supplies this seawater desalination antiscalant for Thailand plants specifically to address those conditions. The product is compliant with TISI (Thai Industrial Standards Institute) requirements and PCD (Pollution Control Department) discharge regulations.
The formula works at the 55 to 70 bar pressures SWRO membranes run under — where standard brackish-water antiscalants lose effectiveness. It keeps calcium carbonate, calcium sulfate, barium sulfate, strontium sulfate, magnesium hydroxide, and silica in solution through the entire membrane train, and disperses colloidal matter and marine organic material that would otherwise co-deposit with scale. The result: stable permeate flow, lower pressure drop, and fewer acid cleanings — critical for Map Ta Phut petrochemical operations where process water supply cannot be interrupted, and for Rayong and Chonburi power plants where boiler feed water quality is essential.
For Thailand's SWRO operators, the biggest cost lever is energy. Scale on SWRO membranes forces higher pump pressure to maintain output, and for petrochemical and power plant operations running 24/7, that translates directly into kWh per cubic meter. Plants using the correct antiscalant dosage typically see 8–15% lower specific energy consumption compared to those running without adequate scale control. For island resorts in Phuket and Krabi that rely on desalinated water for guest supply, the extended membrane life and reduced CIP downtime directly support high-season operations.
| Parameter | Value / Description |
|---|---|
| pH (as such) | 9.0 to 10.0 |
| Appearance | Pale Yellow Liquid |
| Water Solubility | Completely Soluble |
| Solid Content | 33% to 34% w/w |
| Specific Gravity | 1.17 to 1.23 |
| Recommended Dosage | 2 – 6 ppm |
| Chemical Composition | Functional phosphino carboxylic acid with advanced silica dispersants |
Recommended Applications in Thailand: Map Ta Phut petrochemical complex desalination plants; Rayong and Chonburi power plant SWRO systems; Phuket, Krabi, and Koh Samui resort desalination units; Laem Chabang port industrial water supply; Songkhla coastal industrial desalination; Bangkok metropolitan coastal water supply projects; and any Thailand coastal facility requiring reliable freshwater from seawater.
Dosing & Application: Dose continuously into the SWRO feed line after pretreatment and before the high-pressure pump, using a metering pump calibrated to your plant's flow rate. Typical dosage ranges from 2 to 6 ppm depending on feed TDS, temperature, and membrane configuration. For Thailand plants that see significant variation between dry-season and monsoon-season feed conditions, we recommend periodic re-calibration based on updated seawater analysis.
Storage & Handling: Store in original sealed containers in a cool, dry area away from direct sunlight and heat at your Thailand facility. During monsoon season, keep containers off damp floors and away from condensation to prevent contamination. Use appropriate PPE (splash goggles, gloves, apron) during handling. Refer to the Material Safety Data Sheet (MSDS) and Technical Data Sheet (TDS) — both available in Thai and English, compliant with TISI regulatory documentation requirements.
Export & Technical Support for Thailand: We ship to Laem Chabang, Bangkok (Klong Toey), Map Ta Phut, and Songkhla ports, with onward transport to Rayong, Chonburi, Phuket, Krabi, and other coastal industrial and resort sites across Thailand. All shipments include complete customs documentation, MSDS, and TDS in Thai and English. Our technical team provides free dosage calibration based on your seawater analysis — including Langelier Saturation Index, Stiff & Davis Index, and silica saturation calculations — for your specific site conditions.